HamGeek Z7SDRLite 9363 Maker Version Software Defined Radio Development Board XC7Z020 (Acrylic Shell) Compatible with PlutoSDR

Main Chip Parameters:
- Master chip model: XC7Z020-2CLG484I
- Chip level: industrial
- Clock recommended maximum speed: FPGA PLL/MMCM recommended maximum 628M
- PS application processor model: for ZYNQ onboard hardcore processor, dual core Cortex-A9, main frequency of 766M
- DDR specification model: 1024MByte (1GB), 32 bit width, 1066M data rate, MT41K256M16TW-107
- Logic unit: 85K
- Lookup table: 53200
- DSP unit multiplier: 220
- Trigger (FlipFlops): 106400
- Ram: 4.9MBit
- Component temperature range; industrial -40 to 85℃
- Speed level: -2

Z7SDRLite functional interface description:
- Development board power supply: power supply through USB/DEBUG Type-C, 5V input; device power consumption about 3 - 6W (different applications and firmware have varying power consumption)
- Development board clock: 33.33M (PS), 50M (PL), 40M (VC-TCXO-0.5PPM)
- External clock: AD936X reserved external clock input, IPEX1 interface
- USB interface: one USB interface, support USB2.0 virtual network port
- Serial port/JTAG: 1 x FT2232HQ 2-in-1, support UART/JTAG
- Ethernet interface: 1 x PS gigabit Ethernet, RTL8211E
- Expansion IO port: 1 x BTB connector, model of X0802WVS-60AS-LPV01, lead out 40 IOs, 4 pair of differential/32 single-ended, voltage can be modified
- LED and button: POR reset/PL_RSTN/DFU button/USR/PWR/DONE indicators
- Boot setting switch: one BOOT toggle switch for boot setting
- Onboard FLASH: 32MBytes, model of MT25QL256ABA1EW9-0SIT
- SD interface: one SD interface of TF card slot, support SD boot
- GPS module: onboard a MAX M10S GPS module
- EEPROM: onboard a 24C02, PL terminal
- Synchronization: reserve SYNC and IPEX1 of AD9361; ignore AD9363, not supported
- Note 1: Expansion IO port support 4 pairs of differential and 2.5V LVDS_25.
- Note 2: 32 single-ended IOs. Differential wiring is not supported.
- Note 3: The default voltage for expansion IO ports is 2.5V, which can be modified to 1.8V/2.5V/3.3V by oneself.

AD9363 Parameters:
- Master chip model: AD9363bbcz
- ADC/DAC resolution: 12Bit
- Signal data bit width: up to 20MHz
- Channel number: 2 receiving and 2 transmitting/2x2; each channel support for IQ
- Transmitting RF range: 325MHz - 3.8GHz
- Receiving RF range: 325MHz - 3.8GHz
- Receiving noise ration: 2.5dB (800MHz LO)
- Transmitter performance:
  TX EVM: ≤-34dB
  TX noise: ≤-157dBm/Hz
  TX monitor: dynamic range≥66dB, precision = 1dB
- Local oscillator step length: 2.4Hz max.
- Synchronization: it does not support for SYNC
- Gain control: support automatic gain/manual setting gain

RF Functional Interfaces Parameters:
- Antenna interface: SMA female connector
- Clock: 1pcs 40MHz/0.5ppm VC-TXCO
- External clock: support AD936X external clock
- RF LDO linear power supply: wireless LO power supply 1.3V/4A power supply 2-channel RF LDO; PSRR: 40dB (500kHz); noise: 4.4uVRMS (0.8V)
- Impedance control: RF front-end to SMA antenna, control 50ohms microstrip line
- Front-end balun: 1:1, TCM1-63AX+, 10M - 6GHz
- TX power amplification: TX channels all equipped with power amplification output, about 15dB/800MHz, amplifier noise ratio is about 3.8dB
- Onboard GPS PPS precision: RMS 30ns

Firmware Boot and Sampling Rate:
- For PlutoSDR firmware: support 1R1T, 5MSPS, using USB virtual Ethernet port
- For PlutoSDR firmware: factory FLASH firmware
- For FMCOMMS3 firmware: support 2R2T, 10MSPS, using 1000M Ethernet port
- For FMCOMMS3 firmware: SD card boot, you need to prepare SD card by yourself to write mirror image

Package Included:
- 1 x HamGeek Development Board
- 1 x Type-C Data Cable
- 1 x SMA Cable
- 1 x FM Telescopic Antenna
- 1 x Acrylic Plate
- 1 x Pack of Screws