HamGeek ATU-130 200W/150W 3.5-54MHz HF Automatic Antenna Tuner Shortwave Antenna Tuner

HamGeek ATU-130 200W Antenna Tuner with Black Panel:
Description:
HamGeek ATU-130 is a 200w automatic antenna tuner. Improved on the basis of ATU-100, it is a miniature antenna tuner, your ideal HAM supplies.

Compared with ATU-100, it has these advantages:
- Fast MCU
- Better relay
- Better capacitor
- Bigger magnetic
- Thicker wire diameter
- Great power tolerance

Features:
- Adopt PIC18F2520, MCU (faster)
- Miniature HF automatic antenna tuner
- 8-20W tuning
- The third version adopts 4pcs large magnetic ring inductors, producing less heat that the previous version
- Adopt HF32, 10A, HF33, 5A relay
- Using high-voltage ceramic capacitors
- Maximum measurable SSB 225w max. It is recommended to use SSB not more than 200w for a long time. As for other continuous modes, not more than 130W (FT8, CW, FM)
- Size: 38 x 88 x 155mm/1.5 x 3.5 x 6.1" (without the size of protrusions)
- 0.5kg net weight: Portable to carry. Suitable for vehicle, indoor and outdoor fixed, etc.
- 3.5-54MHz (specifically affected by the length of the antenna and the degree of deviation of the standing wave)
- Tuning impedance range of 5Ω-1.2KΩ
- Can be used for various antennas, including long-line antennas (recommended), GP (recommended), inverted V, dipole, etc., to adjust standing waves and match the impedance of shortwave receivers. For antenna systems and feeder systems with baluns, the tuning range will be limited

Package Included:
- 1 x Set of HamGeek Antenna Tuner

Instructions:
Connect the power cord to 11-14vDC power supply. Connect a shortwave radio to the IN RF line of the automatic tuner. Connect a ground wire. The antenna is connected to the ANT of the tuner (M seat or quick socket). With Am, fm, cw 10-20w well tuned (within swr1.5), you can use high power.

Attention:
If manual operation is required, you can press auto once, the small dot in the middle of the screen LC will disappear, and the instrument is in manual mode. Press it again to switch to automatic mode. In special cases, after pressing tune to reset, the LC combination is set to zero.
---------------------------------------------------------------------------------------------------------------------------------

HamGeek ATU-130 150W Antenna Tuner with Blue Panel:
Description:
HamGeek ATU-130 is a 150w automatic antenna tuner. Improved on the basis of ATU-100 hardware, it is an universal type.

Features:
- Adopt PIC18F2520, MCU
- Using 4pcs T94 magnetic ring inductors, the coil above 1mm, the withstand power is greater, and the heat is much smaller than the original one
- Use HF32, 10A, HF33, 5A relays (similar to that for ICOM AT130)
- Adopt 6KV high-voltage capacitor with low loss
- Miniature shortwave automatic antenna tuner

Parameters:
- Coverage frequency: 3.5-54MHz
- Tuning impedance range: 5Ω-1.2KΩ
- Tuning power: 5-15W
- Transmit power: SSB 160w max
- Maximum measurable power: 180w
- When the initial standing wave deviation is large, it is recommended to use the SSB not more than 150w for a long time. (FT8, AM, FM, CW is not more than 100W. When the deviation of the standing wave before adjustment is large, reduce the power as appropriate)
- Size: 38 x 88 x 155mm/1.5 x 3.5 x 6.1" (without the size of protrusions)
- Power supply: 11-14VDC power supply

Package Included:
- 1 x Set of HamGeek Antenna Tuner

Instructions:
- Connect the power cord to 11-14vDC power supply. Connect a shortwave radio to the IN RF line of the automatic tuner. The antenna is connected to the ANT of the antenna tuner (M seat or quick socket). With Am, fm, cw 6-15w well tuned (within swr1.5), you can use high power.
- If the standing wave is too large and the tuning is not successful, high-power transmission cannot be used, because it may damage the antenna tuner or shortwave radio. Please remove the fault and then transmit with high power.
- Good grounding is good for standing wave tuning. If it is unconditionally grounded, connect the grounding end of the tuner to the grounding of shortwave radios.

Attention:
- The product defaults to automatic mode.
- If manual operation is required, you can press auto once, the small dot in the middle of the screen LC disappears, and the instrument is in manual mode. Press it again to switch to automatic mode. In special cases, after pressing tune to reset, the LC combination is set to zero.